Product Details
Hemispherical Self Adhesive Rubber Feet
Product Specifications
- Material
- EPDM/NR/SBR/Silicone
- Hardness
- 50-60 Shore A
- Temperature Range
- Confirm the rubber compound and adhesive system for the application temperature, substrate and exposure duration.
- Colors
- Black, white. Custom colors can be matched to your Pantone color code.
Self adhesive rubber feet can be customized to your dimensions, shape and material requirements.
Available Sizes
Dimensions are in mm unless otherwise indicated.
| Part No. | OD | H | Material | Color |
|---|---|---|---|---|
| ARF1001 | 3.5 | 1.5 | ||
| ARF1002 | 4.7 | 3 | Silicone | White |
| ARF1003 | 5 | 1.5 | Silicone | Transparent |
| ARF1004 | 5 | 2.5 | Silicone | Transparent |
| ARF1005 | 6 | 2 | ||
| ARF1006 | 6 | 4 | Silicone | Transparent |
| ARF1007 | 7 | 1.5 | ||
| ARF1008 | 7 | 2 | Silicone | White |
| ARF1009 | 7 | 2 | NR | Black |
| ARF1010 | 7.5 | 1.5 | Silicone | White |
| ARF1011 | 8 | 1.5 | NR | Black |
| ARF1012 | 8 | 1.5 | ||
| ARF1013 | 8 | 2 | ||
| ARF1014 | 8 | 2.5 | ||
| ARF1015 | 8 | 3 | ||
| ARF1016 | 8 | 3 | ||
| ARF1017 | 8 | 4 | Silicone | Transparent |
| ARF1018 | 9 | 2 | NR | Black |
| ARF1019 | 9.5 | 2 | NR | Black |
| ARF1020 | 9.5 | 3.7 | ||
| ARF1021 | 9.8 | 5 | NR | Black |
| ARF1022 | 9.8 | 8 | Silicone | Transparent |
| ARF1023 | 10 | 1.5 | ||
| ARF1024 | 10 | 2 | ||
| ARF1025 | 10 | 3 | ||
| ARF1026 | 10 | 4.5 | NR | Black |
| ARF1027 | 10.8 | 5 | NR | Black |
| ARF1028 | 11 | 4.8 | ||
| ARF1029 | 11 | 5 | Silicone | White |
| ARF1030 | 11 | 5 | Silicone | Transparent |
| ARF1031 | 12 | 8 | Silicone | Transparent |
| ARF1032 | 12.4 | 5.5 | NR | Black |
| ARF1033 | 13.2 | 6 | NR | Black |
| ARF1034 | 14.7 | 2 | NR | Black |
| ARF1035 | 16 | 8 | ||
| ARF1036 | 16 | 10 | Silicone | Transparent |
| ARF1037 | 18 | 10 | ||
| ARF1038 | 19 | 10 | Silicone | White |
Can’t find your size? Need a custom foot?
Send your dimensions, mounting details and quantity, or attach a drawing. We’ll help you review a custom size, shape or material for your application.
FIT & APPLICATION GUIDE
Place the dome where the moving part actually meets it
The flat circular base bonds to the substrate while the rounded dome makes contact. The contact patch changes as the dome compresses, so check the intended closing path.
01 / BEFORE YOU CHOOSE
What to measure for this profile
- Base diameter OD
- Check that the full adhesive circle fits on a flat mounting area.
- Unloaded height H
- Compare the dome height with the door or cover gap. Confirm the compressed position on a sample.
- Contact position
- Mark where the opposing surface meets the dome. An off-center strike can push sideways on the bond.
02 / INSTALLATION
Align the dome with the closing path
Trial the location with the liner on
Move the door or cover slowly and identify its contact point. Avoid placing the dome on a hinge sweep or sharp edge.
Prepare the bonding circle
Clean and dry the mounting surface according to the selected adhesive instructions.
Attach the flat base
Remove the liner and apply pressure as required by the backing supplier while supporting the substrate.
Check closure after bonding
Wait the specified bond time, then verify closing gap, latch operation and edge lift during repeated trial cycles.
03 / USE & CHECK
Where to use this profile
Cabinet and enclosure stops
Locate a dome where a moving panel needs a rubber contact point without a drilled fixing.
Small contact clearances
Evaluate the compressed dome height; OD and unloaded H do not determine the final closing gap alone.
For a selection review: OD and H, closing gap, contact path, panel finish and expected cycle frequency. Send your application details →
Need a different size or shape?
Tell us what you need. We'll help you find the right rubber or silicone part and prepare a quote.