Product Details
Rubber Feet For Chairs
Product Specifications
- Material
- EPDM/NR/SBR/CR/Silicone. Compound selection depends on the application, including any RoHS, odor or environmental requirements.
- Hardness
- 30-85 Shore A
- Temperature Range
- Confirm the selected compound, service temperature, exposure duration and operating medium before ordering.
- Colors
- Black, white. Custom colors can be matched to your Pantone color code.
Installation
Press the feet onto matching table or chair legs. No adhesive is needed for a correctly sized push fit.
Applications
Fit to table and chair legs to help protect floors, reduce scraping noise and improve grip.
Need custom rubber bumpers? Send us your dimensions, material and application requirements.
Available Sizes
Dimensions are in mm unless otherwise indicated.
| Part No. | A | B | C | D | Material | Color |
|---|---|---|---|---|---|---|
| RFE5101 | 11 | 6 | 16 | 16 | EPDM/NR/SBR/CR/Silicone | Black/White/Gray |
| RFE5102 | 16.6 | 12.6 | 19.6 | 16 | EPDM/NR/SBR/CR/Silicone | Black/White/Gray |
| RFE5103 | 18.8 | 14.7 | 25.7 | 18 | EPDM/NR/SBR/CR/Silicone | Black/White/Gray |
| RFE5104 | 22.1 | 18.5 | 28.1 | 20 | EPDM/NR/SBR/CR/Silicone | Black/White/Gray |
| RFE5105 | 22.25 | 17.8 | 28.55 | 20 | EPDM/NR/SBR/CR/Silicone | Black/White/Gray |
| RFE5106 | 24.4 | 20.8 | 30.78 | 20 | EPDM/NR/SBR/CR/Silicone | Black/White/Gray |
| RFE5107 | 27.51 | 23.5 | 33.2 | 20 | EPDM/NR/SBR/CR/Silicone | Black/White/Gray |
Can’t find your size? Need a custom foot?
Send your dimensions, mounting details and quantity, or attach a drawing. We’ll help you review a custom size, shape or material for your application.
FIT & APPLICATION GUIDE
Check the chair leg and the floor-facing base
This short round chair foot fits around a leg end. The internal opening controls the fit, while the wider outer body and underside determine clearance and floor contact.
01 / BEFORE YOU CHOOSE
What to measure for this profile
- Opening B
- Compare with the round leg OD. Outside rim A is a clearance dimension and should not be used as the fitting diameter.
- Base C
- Check the underside width against nearby legs or frame members. Inspect the actual contact pattern on a sample.
- Cavity depth D
- Measure how far the leg can enter. Note angled cuts or splayed legs that could load one edge of the foot.
02 / INSTALLATION
Seat the cup, then check the chair stance
Check the leg cut
Clean the end and remove burrs. Record any angle rather than assuming a flat cut.
Fit the round cavity
Press the foot evenly around the leg until seated. Keep the mouth from rolling inward.
Check all contact points
Stand the chair upright and check whether each foot contacts the floor. An angled leg may need a different profile.
Trial normal movement
Check grip, floor marking and pull-off during repositioning. Inspect trapped grit during routine cleaning.
03 / USE & CHECK
Where to use this profile
Round chair legs
Review the opening and cavity depth together when replacing an existing cup-style foot.
Splayed furniture legs
Test the actual leg angle; a nominal diameter match does not guarantee even floor contact.
For a selection review: Leg OD, end angle, insertion depth, required base width and floor finish. Send your application details →
Need a different size or shape?
Tell us what you need. We'll help you find the right rubber or silicone part and prepare a quote.